|
Two-stage / with cord, plug, and switch / with thermal protector
|
 |
| |
ULVAC KIKO's Direct-Drive Oil-Sealed
Rotary Vacuum Pumps are the sliding vane "Gaede
Type". Oil is used to lubricate the rotary mechanism
and to seal the vacuum pumping chamber, producing excellent
vacuum stability and reliability. Small direct-drive
pumps feature faster start-up and quicker pump down compared
to belt-driven pumps. In addition, ULVAC KIKO 's G-Series
Oil-Sealed Rotary Vacuum Pumps are cost-effective and
operate quietly.
G-Series pumps are available in single and dual stage versions
with pumping speeds ranging from 5 L/min. to 100 L/min.. |
|
| |
Unit |
50Hz |
60Hz |
| Actual Pumping Speed |
L/min. |
100 |
120 |
| Ultimate pressure |
Pa |
6.7 x 10-2 (6.7×10-1)
(6.7)
|
| Motor |
|
Single
phase, 220V, 400W, 4 poles, capacitor starting |
| Full load current |
A |
1.1 |
1.2 |
| Oil capacity |
mL |
800 |
| Recommended oil |
|
SMR-100 |
| Weight |
kg |
22.4 |
| Inlet port diameter |
mm |
O.D.
dia.27 x I.D. dia.20 |
| Ambient operation temp.range |
°C |
7 – 40 |
| Dimensions |
mm |
173.5(W)
x 460.5(L) x 264(H) |
|
| *Ultimate pressure is measured with Macleod gauge. In ( ) shows the measurements with Pirani gauge. |
| 1. |
Ensure the proper oil
level and oil condition are maintained at all times. |
| 2. |
Before stopping a pump
it should be vented to atmosphere to prevent the back-streaming
of oil. (Contact your local sales representative for applications
assistance.) |
| 3. |
When operating a pump
for long time above 0.1MPa, it is possible that
oil mist be exhausted from the exhaust port. Installation
of Oil mist trap (OMT Series) will eliminate this potential source of contamination. |
| 4. |
Oil-sealed rotary
pump is not recommended for continuous operation near atmospheric
pressure. |
Optional suction port
|
|
Size
|
Note
|
| Suction pipe for hose |
Dia.27 |
Attached to
standard type
|
| Suction pipe for hose |
Dia.8 |
Option. 40X40adapter is needed, use
the suction pipe /40X40 adapter
|
| Suction pipe for hose |
Dia.12 |
Option. 40X40adapter is needed, use
the suction pipe /40X40 adapter
|
| Suction pipe for hose |
Dia.15 |
Option. 40X40adapter is needed, use
the suction pipe /40X40 adapter
|
| Suction pipe for hose |
Dia.18 |
Option. 40X40adapter is needed, use
the suction pipe /40X40 adapter
|
| Suction pipe for hose |
Dia.22 |
Option. 40X40adapter is needed, use
the suction pipe /40X40 adapter
|
| KF-25 suction port |
KF-25 X
(20X20) |
Option |
| A type suction pipe |
PT1/4-L20,male |
Option. 40X40adapter is needed, use
the suction pipe /40X40 adapter
|
| B type suction pipe |
PT1/4-L20,female |
Option. 40X40adapter is needed, use
the suction pipe /40X40 adapter
|
| C type suction pipe |
PT1/4-L10,male |
Option. 40X40adapter is needed, use
the suction pipe /40X40 adapter
|
|
Optional exhaust port
|
|
Size
|
Note
|
| Exhaust port cap |
-
|
Attached to standard
type
|
| Exhaust pipe for hose |
Dia.27 |
Option |
| KF-25 exhaust port |
KF-25 |
Option |
|
Trap for exhaust side
|
|
Model
|
Note
|
| Oil-mist trap |
OMT-100A |
Option |
| In-line type oil-mist trap |
OMI-100 |
Option |
|
| Voltage |
Applicable
Volt |
CE Marked |
CSA Marked |
cTUVus Marked |
| Single phase, 100V |
Standard |
|
|
|
| Single phase, 200V |
 |
|
|
|
| Single phase, 240V |
 |
|
|
|
| Three phase, 200V |
 |
|
|
|
|