|
Two-stage / with cord, and switch
|
 |
| |
Our company's Direct-drive Oil Sealed Rotary Vacuum Pump is the Sliding Vane "Gaede type". It employs oil in the vacuum pump to lubricate the rotary part and to allow sealing effect upon vacuum formation, thus obtaining a high degree of stable vacuum and high reliability. This small direct-drive motor excels over belt-driven types both in quickness of starting and pumping. |
|
| |
Unit |
50Hz |
60Hz |
| Actual Pumping Speed |
L/min. |
20 |
24 |
| Ultimate pressure |
Pa |
1.3
x 10-1 |
| Motor |
|
Single
phase, 220V, 100W, 4 poles, split phase starting |
| Full load current |
A |
1.7 |
1.4 |
| Oil capacity |
mL |
180 |
| Recommended oil |
|
SMR-100 |
| Weight |
kg |
9 |
| Inlet, outlet pipe diameter |
mm |
O.D.
 18 x I.D. 14 |
| Ambient operation temp.range |
°C |
7 – 40 |
| Dimensions |
mm |
156(W)
x 295.5(L) x 199.5(H) |
|
| *Ultimate pressure is measured with Macleod gauge. |
| 1. |
Ensure the proper oil
level and oil condition are maintained at all times. |
| 2. |
Before stopping a pump
it should be vented to atmosphere to prevent the back-streaming
of oil. (Contact your local sales representative for applications
assistance.) |
| 3. |
When operating a pump
for long time above 0.1MPa, it is possible that
oil mist be exhausted from the exhaust port. Installation
of Oil mist trap (OMT Series) will eliminate this potential source of contamination. |
| 4. |
Oil-sealed rotary
pump is not recommended for continuous operation near atmospheric
pressure. |
Optional suction port
|
|
Size
|
Note
|
| Suction pipe for hose |
18 X
M20 |
Attached to
standard type
|
| Suction pipe for hose |
8 X
M20 |
Option |
| Suction pipe for hose |
12 X
M20 |
Option |
| Suction pipe for hose |
15 X
M20 |
Option |
| Suction pipe for hose |
22 X
M20 |
Option |
| KF-25 suction port |
KF-25 X
M20 |
Option |
| A type suction pipe |
R1/4-L20 (male) X
M20 |
Option |
| B type suction pipe |
Rc1/4-L20 (female) X
M20 |
Option |
| C type suction pipe |
R1/4-L10 (male) X
M20 |
Option |
| Suction pipe with filter |
9 |
Option |
|
Optional exhaust port
|
|
Size |
Note |
| Exhaust port cap |
- |
Attached to
standard type |
| Exhaust pipe for hose |
15 X
G3/4 |
Option |
| Exhaust pipe for hose |
18 X
G3/4 |
Option |
| KF-16 exhaust port |
KF-16 X
G3/4 |
Option |
| KF-25 exhaust port |
KF-25 X
G3/4 |
Option |
|
Trap for exhaust side
|
|
Model
|
Note
|
| Oil-mist trap |
OMT-050A |
Option |
|
| Voltage |
Applicable
Volt |
CE Marked |
CSA Marked |
cTUVus Marked |
| Single phase, 100V |
Standard |
|
|
|
| Single phase, 115V |
 |
|
|
|
| Single phase, 200V |
|
|
|
|
| Single phase, 220V-230V |
|
|
|
|
|
